The first pre-installation considerations :
① according to the selected product placement into the water faucet and fittings .
Pipeline must be flushed ( red to pipe debris ) ② before installing the product .
③ Turn off the main valve after installing the product ( be careful not to bruise the product ) .
④ post- installation tests: 1 ) Sealing of joints , 2 ) left and right heat cold , 3 ) are securely installed.
⑤ test and debug OK.
⑥ clean up the site , handed users, the initial description of the use , to avoid misuse .
Section Installation Notes :
1 , countertop basin ( Kitchen ) faucet installation :
① general countertop height 80-85CM, leading into the water and the accompanying long 35CM, so water interface should be at ground level 55-60CM, there is no margin to avoid the connection . ( The above is for reference only , according to the product roadmap hydropower discharged into water , drain bit line position lights , etc. ) .
② water interface between the pipes leading into general use Angle connector for easy faucet repair, replacement ( do not go off the main switch ) .
③ mesa bottom hole faucet should be combined with a uniform , after assembly, the gasket or gaskets have a certain amount of compression , to prevent leakage and loosening of the faucet body .
④ attention nuts when installing a fast way to install the lock .
2 , wall-mounted bath ( shower ) faucet installation.
① faucet body mounting height should be easy to handle grip , the proposed height is 100CM. Water installation dimensions pitch to the requirements of high- level water interfaces should avoid leading tilt after installation.
② water sealing tape wrapped around the pin ( ie, with raw material ) should be screwed into the wound in the opposite direction .
③ install the nut with cone filters generally conical tip direction to the wall installation .
④ shower outlet height is set according to family members , generally available and raising his hand at . But not too low ( to avoid colliding with shower body damage ) , it is recommended from the ground 160-180CM.
3 , into the wall bath ( shower ) faucet installation.
① influent and effluent pipes, body position should draw the line , then Poqiang installation.
② faucet body mounting height should be easy to operate. Water pitch to installation dimensions requirements. Water interface should be level , contours , the outlet pipe should be vertical , inclined to avoid the appearance of a leader after installation.
③ outlet , shower position reference installation dimensions , easy to use the principle of family members .
④ connection must be wrapped around the pipe sealing tape ( Teflon tape ) . All water is connected, turn on the water at each junction painted plastic , then sealed the wall . There are panels cover the walls where wall décor can be omitted .
4, a special faucet installation.
① removable kitchen faucet , its weight should be fixed at the lowest sprinkler hose ( shower in the socket ) , and slightly better direction shower , shower down easy fixed .
② faucet attached to the gun , the gun outlet installation , locking nut at the bottom . Water through the outlet end of the gun , connected with the leading brass gun below .
③ separate faucet , is screwed into the connection ( outer teeth ) can be connected to the junction wrapped or coated with waterproof adhesive sealing tape to prevent leakage. Then follow the size chart layout, install the subject. Nut washer must confirm the connection . External water inlet pipe is connected to the last .
④ Ming tube shower faucet , installation order : subject, Ming , bends group shower . To avoid distortion due to the fixed connection tube length as a result of the Ming . Sealing tape wrapped around the junction ( raw material belt ) .
Section faucet maintenance.
1 , the leading case of intermittent use of long-life products ( durables ) , if used , properly maintained, prolong its useful life.
1 ) Water conditions :
① silt content , easy blocked or reduced life expectancy , increase in the inlet end of the misplaced pads, and regular cleaning . PH value of the anomaly, the chromium layer and seals will damage , be sure to improve water quality or require special .
② pressure instability , the abnormal amount of water , accompanied by the sound of manic or mixed hot and cold disorders. Regulate water pressure or pressure balance valve or the optional installation of a special leader, such as thermostats , etc. .
2 ) cleaning agent :
Choose neutral , mild , non-abrasive cleaning supplies. Fine cotton cloth dampened with clean , final rinse with water .
2 Maintenance :
1 ) consider the net cleaning , network with consideration of wave devices ( bubbler ) should be cleaned according to usage : use a small wrench wave device ( bubbler ) gently removed, taken into account the net for cleaning , after cleaning as is replacing . Washing water network account joints , cleaning according to the use .
2 ) Exterior cleaning: white cotton cloth moistened with colorless glass cleaner, water, or 1% soapy water to clean the surface of the product .
2 ) Product loose : the product is installed countertops loose , fixed with a suitable tool. Handle loose, with a special wrench or Allen wrench to tighten .
3 , faucets use
Open supple, close place to stop . Leading switch , rotating parts are more sophisticated, so vigorously and unreasonable actions may cause malfunction or damage , or even continue to use. To ensure your safety in the use of hot and cold mixing faucet , turn the cold water , and then open the hot water , and gradually increase until the water temperature right ( left and right hot cold ) . Pulling commutation should be in place to avoid the pressure caused by runaway fusion .